CALL US TODAY
202.772.2039

Changes to the Buy American Regulations

Made in the USA - Changes to the Buy American Regulations

There have been fairly significant changes to the Buy American rules under both the Federal Acquisition Regulation, or FAR, and the Defense Federal Acquisition Regulation Supplement, or DFARS. They relate to when a product qualifies as a domestic end product, and thereby is eligible for the Buy American bidding preference.

Watch as George Thompson, international trade attorney, details the impact of these recent changes.

Transcript of Expansion of Investment Restrictions on Chinese Military Companies

Hello again, this is George Thompson, and today I’d like to discuss recent changes to the Buy American regulations. Now, since it’s summertime in Washington and this is a real snoozer of a topic, I decided to wear a completely inappropriate shirt to lighten the mood. I hope you don’t mind.

But seriously, there have been fairly significant changes to the Buy American rules under both the Federal Acquisition Regulation, or FAR, and the Defense Federal Acquisition Regulation Supplement, or DFARS. They relate to when a product qualifies as a domestic end product, and thereby is eligible for the Buy American bidding preference.

By way of background, most federal contracts are subject to the Trade Agreements Act’s rules regarding product origin. The Buy American rules apply when TAA rules do not. Their main use is in procurements made by certain federal agencies, primarily the Defense Department, and by all agencies, if the contract value is below $183,000.

Generally speaking, a product is a domestic end product if it meets two requirements. First, it must be manufactured in the United States, and second, a specified percentage of its components must be of U.S. origin.

The recent changes pertain to that second requirement, the value of components used in making the product.

The minimum percentage of U.S.-value content will increase, from 55 percent now to 60 percent this coming October. So, U.S. producers may have to adjust their component sourcing to be sure that they meet the heightened requirement. Although October may seem a long time away right now, recent supply chain issues and shortages will make the changeover more challenging than we might otherwise expect.

Under both the FAR and DFARS, commercial off-the-shelf products are not subject to the component value criterion, and remain eligible based solely on manufacture in the United States.

Next, a totally new rule is imposed for products that consist wholly or predominantly of iron or steel. Except for fasteners, they are now excluded from the commercial off-the-shelf waiver.

Moreover, to qualify as a domestic end product, the cost of any foreign-origin iron and steel it incorporates must account for less than 5 percent of the cost of all the components used in its manufacture.

Therefore, domestically-produced items with a 5 percent or higher value percentage of foreign iron or steel content no longer will meet the definition of domestic end product.

Obviously, this change too will require material sourcing adjustments by manufacturers of products covered by it.

One additional point about the DFARS. Unlike the FAR, it provides that products of certain designated qualifying countries which have entered into reciprocal defense trade procurement agreements with the United States are eligible products as well, just as if they were of U.S. origin. Likewise, content from those countries is treated the same as domestic content for purposes of reaching both the 55 percent value requirement and the iron and steel content. For the DFARS, then, the impact on material sources may not be as significant.

One final point, the newly-effective Build America, Buy America Act has new content requirements for federal grant programs, including the Federal Aviation Administration, Federal Transit Administration and Federal Highway Administration. Specifically, it imposes a “domestic content procurement preference” for federally-funded infrastructure projects, requiring that:

first, all iron and steel used in the product or project are produced in the United States;
second, the manufactured products used in the project are produced in the United States; and
third, the construction materials used in the project are produced in the United States.

It doesn’t appear that there will be an immediate impact on Transportation Department grant program requirements. Nevertheless, recipients of such grants, and their product suppliers, should keep an eye on developments here as well.

Thanks for tuning in, and I hope to see you again soon.

Thompson & Associates, PLLC provides representation in all aspects of customs laws and regulations, specializing in export and import regulations and international business counseling. We can be reached at 202-772-2039 or online.

SHARE THIS ARTICLE
Facebook
Twitter
LinkedIn
WhatsApp
Email
Print
SUBSCRIBE TO OUR EMAIL NEWSLETTER

Get delivered once a week to your inbox, a hand-picked list of the latest news on international trade compliance issues as well as the latest articles from George W. Thompson.

MORE VIDEOS